Do-It-Yourself Drywall Tips

Drywall is the popular term for pre-fabricated plaster wall panels. These panels are easy to install, but can take some hard work to repair. Therefore, your best bet is to avoid basic mistakes when installing your drywall to save yourself the headache of having to redo the job.

One of the best Kings Drywall tips concerns the surface on which the drywall is to be installed. Walls must be flat and framing has to be straight at right angles, or true. Studs or rafters that are bowed must be planned to flatten them before work begins. To test the walls, stretch a piece of string across it to determine if the studs are all on the same plane. Redo as necessary.

Cutting drywall doesn’t have to involve sawing at a panel until the sections separate. You’ll only end up with a prematurely-dull utility knife and a scratched surface underneath. Draw a line across the panel of drywall you want to cut, ensuring that it is completely straight with the aid of a drywall T-square. Score down this line just deep enough to cut through the backing paper. Then, just lift the panel and snap it right down this guide-line. Complete the cut by slicing through the remaining layer of backing paper and smoothen any rough edges.

It’s easy to go overboard when applying the joint compound, or mud, when it comes to taping and mudding your drywall. Some people work their joint too much, too early, and this is a no-no! Good drywall tips instruct to first apply the tape, and spread a thin layer of compound over the tape to embed it. Leave it to dry before scraping it slightly to level any high spots and apply a second layer if needed.

Drywall hanging may seem simple initially, but those who have attempted it know that installing drywall correctly can be a lifelong learning process. Those who can never seem to get it right can take heart; success is the preserve of a select few.

Whether you’re building a new home, remodeling an existing one, or doing any sort of drywalling, that requires a building permit or an engineer’s approval, make sure that you check to make sure, that you are allowed to switch the direction of the drywall.

One of the worst things that can happen to any builder or contractor, is to finish an entire drywall job, only to find out later that they need to remove the drywall, because they ran it in the wrong direction.

It’s becoming pretty popular, for contractors who are working with metal studs, for tenant improvements to run their drywall vertically. This seems to work pretty good for these building and remodeling contractors, but make sure that you’re allowed to do it first. Some of these contractors, aren’t getting the necessary permits, and this might create a problem for the owner of the building later on down the road.

It’s a new way of drywalling, and it seems to provide these drywall contractors with a more efficient way of drywalling certain areas. One of the only ways that you can drywall vertically, and have it work for you in an effective way, is to make sure that your stud layout is correct.

You will need to make sure that you lay out your vertical framing, 48 inches on center, otherwise you will not be able to install the drywall vertically, in an effective manner. Make sure that you lay out for all of your door and window openings, so that you don’t waste very much drywall.

Most engineers and building apartments, require homes and other structures, to install the drywall horizontally. This seems to add more strength to the building and have less problems when finishing the drywall, then running it vertically.

Just make sure you check with any of your local building departments, before applying the drywall vertically. You can save yourself a lot of frustration, with a simple visit to your building department.

Make sure that you get these approvals in writing, or I would suggest that you don’t do it. Take it for me, one of the most important things that you can do, when working with the building department, architects are engineers, is to get everything in writing.

Drywall Installation Pictures and Tips

If You Live in Northern San Diego County or South Orange County, and You’re Looking for a Great Contractor, Click on This Link Drywall and Building Contractors

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He has just finished a Home Buyers Guide to take some of the frustration out of home shopping.

Previous Post Next Post